Sponsored by :
All About Iphone
We Will Give you new info for iPhone
These are instructions on how to enable support for carrier bundles in iTunes 8.2 for Windows.
You'll notice if you try to update your iPhone carrier settings using the final version of iTunes 8.2 the .ipcc files are greyed out. In order to re-enabled access to these files you will need to follow the simple steps below.
Step One
Quit iTunes
Step Two
Press Windows Key + R to open the run dialog. Enter in cmd then click OK
Step Three
Enter the following command into the Command Prompt window.
"C:\Program Files\iTunes\iTunes.exe" /setPrefInt carrier-testing 1
Step Four
Connect your iPhone and click to launch iTunes from your Start Menu.
Step Five
Select your iPhone from the list of devices on the left then hold down the Shift key and click the Check for Updates button.
Step Six
Notice you can now select your .ipcc file as it is not greyed out.
0 Comment
These are instructions on how to jailbreak your iPhone 3.0 iPhone firmware using RedSn0w for Windows. The Mac version of this tutorial is here
This tutorial can be used to jailbreak before applying the UltraSn0w unlock.
Step One
Create a folder on your desktop called Pwnage
Download RedSn0wfrom here or here and place it in the Pwnage folder. Likewise, download the latest 3.0 firmware from below and place it in the same folder.
3.0.0 (2G): iPhone1,1_3.0_7A341_Restore.ipsw
3.0.0 (3G): iPhone1,2_3.0_7A341_Restore.ipsw
Extract the RedSn0w zip file to the Pwnage folder.
Step Two
Connect your iPhone to the computer and launch iTunes.
Select your iPhone from the list of devices on the left. Now hold down shift and click the Restore button. Restore is preferred as it won't create any wasted space on your iPhone.
Navigate to the Pwnage folder on your desktop and select the firmware ipsw. Click the Open button to continue.
Step Three
Once iTunes has finished updating your iPhone to the desired firmware you may launch redsnw0w.exe from the Pwnage folder on your desktop.
Step Four
Once RedSn0w opens click the Browse button
Step Five
Select the firmware ipsw we placed in the Pwnage folder on our desktop then click Open
Step Six
Once the firmware has been verified click the Next button to continue.
Step Seven
Make sure Cydia is selected and click the Next button.
Step Eight
Please plug your iPhone into the computer and make sure its OFF then click the Next button
Step Nine
RedSn0w will now guide you through the steps to get into DFU mode.
Hold down both the Home button and the Power button for 10 seconds.
Release the Power button and continue holding the Home button until RedSn0w detects the device.
Step Ten
Your iPhone will now reboot
Step Eleven
RedSn0w will then begin uploading the new RAM Disk.
Step Twelve
Once this is complete you will be notified that RedSn0w is done. Click the Finish button.
When your iPhone finishes reboot (5 minutes or so). It will be jailbroken with Cydia on the SpringBoard.
These are instructions on how to unlock and jailbreak your iPhone 2G on the 3.0 iPhone firmware using RedSn0w for Windows. Before beginning make sure you have updated to iTunes 8.2.
You can find the Mac version of this tutorial here
Step One
Create a folder called Pwnage on your desktop.
Download the following files and place them in the Pwnage folder you just created:
- RedSn0w
- BL 3.9
- BL 4.6
- 3.0.0 (2G): iPhone1,1_3.0_7A341_Restore.ipsw
Extract the RedSn0w zip file to the Pwnage folder.
Step Two
Connect your iPhone to the computer and launch iTunes.
Select your iPhone from the list of devices on the left. Now hold down shift and click the Restore button. Restore is preferred as it won't create any wasted space on your iPhone.
Navigate to the Pwnage folder on your desktop and select the firmware ipsw. Click the Open button to continue.
Step Three
Once iTunes has finished updating your iPhone to the desired firmware you may launch redsnw0w.exe from the Pwnage folder on your desktop.
Step Four
Once RedSn0w opens click the Browse button
Step Five
Select the firmware ipsw we placed in the Pwnage folder on our desktop then click Open
Step Six
Once the firmware has been verified click the Next button to continue.
Step Seven
Make sure Cydia and Unlock is selected and click the Next button.
Step Eight
We will know need to set the location of our bootloader files.
Click Browse and select the 3.9 bootloader file from the Pwnage folder on your desktop.
Click Browse and select the 4.6 bootloader file from the Pwnage folder on your desktop.
Click the Next button to continue.
Step Eight
Please plug your iPhone into the computer and make sure its OFF then click the Next button
Step Nine
RedSn0w will now guide you through the steps to get into DFU mode.
Hold down both the Home button and the Power button for 10 seconds.
Release the Power button and continue holding the Home button until RedSn0w detects the device.
Step Ten
Your iPhone will now reboot
Step Eleven
RedSn0w will then begin uploading the new RAM Disk.
These are instructions on how to jailbreak your iPod (1G or 2G) on OS 3.0 firmware using RedSn0w for Mac. The Windows version of this tutorial is here
Step One
Create a folder on your desktop called Pwnage
Download RedSn0w from here and place it in the Pwnage folder. Likewise, download the latest 3.0 firmware and place it in the same folder.
NOTE*: The iPod touch 3.0 firmware must be purchased from iTunes. iTunes will save the firmware files here:
~/Library/iTunes/iPod Software Updates/iPod2,1_3.0_7A341_Restore.ipsw
~/Library/iTunes/iPod Software Updates/iPod1,1_3.0_7A341_Restore.ipsw
Extract the redsn0w application from the RedSn0w zip file to the Pwnage folder.
Step Two
Connect your iPhone to the computer and launch iTunes.
Select your iPhone from the list of devices on the left. Now hold down shift and click the Restore button. Restore is preferred as it won't create any wasted space on your iPhone.
Navigate to the Pwnage folder on your desktop and select the firmware ipsw. Click the Open button to continue.
Step Three
Once iTunes has finished updating your iPhone to the desired firmware you may launch redsnw0w.app from the Pwnage folder on your desktop.
Step Four
Once RedSn0w opens click the Browse button
Step Five
Select the firmware ipsw we placed in the Pwnage folder on our desktop then click Open
Step Six
Once the firmware has been verified click the Next button to continue.
Step Seven
Make sure Cydia is selected and click the Next button.
Step Eight
Please plug your iPhone into the computer and make sure its OFF then click the Next button
Step Nine
RedSn0w will now guide you through the steps to get into DFU mode. You can find more help with DFU mode here
Hold down both the Home button and the Power button for 10 seconds.
Release the Power button and continue holding the Home button until RedSn0w detects the device.
Step Ten
Your iPhone will now reboot
Step Eleven
RedSn0w will then begin uploading the new RAM Disk.
Step Twelve
Once this is complete you will be notified that RedSn0w is done. Click the Finish button.
When your iPhone finishes reboot (5 minutes or so). It will be jailbroken with Cydia on the SpringBoard.
